Thread Pitch Identifier

The Thread Pitch Identifier matches measured outer diameter and pitch/TPI to NPT, BSP, UNC/UNF, and Metric thread standards. It features an interactive SVG thread profile comparison (60° vs 55° angles), tap drill recommendations, and a cross-reference table across all standards — free, no signup required.

Thread Measurement

Measured Outer Diameter

Measured Pitch

Thread Profile Comparison

NPT/Metric 60°

BSP 55°

UN/Metric 60°

Standard Comparison

Standard	Thread Angle	Tapered	Sealing	Common Use
NPT	60°	Yes	Thread taper (tape/sealant required)	North America plumbing, gas, hydraulic
BSP (BSPT)	55°	Yes	Thread taper	International plumbing, pneumatic
BSP (BSPP)	55°	No	Bonded washer / O-ring	International hydraulic, instrumentation
UNC	60°	No	Mechanical fastening	General purpose bolts (coarse)
UNF	60°	No	Mechanical fastening	Precision bolts, automotive (fine)
Metric (ISO)	60°	No	Mechanical fastening	Worldwide standard fasteners

Thread Reference Table

Designation	Major OD (mm)	Major OD (in)	Pitch (mm)	TPI	Tap Drill (mm)	Tap Drill
1/8" NPT	10.29	0.405	0.941	27.0	8.7	11/32
1/4" NPT	13.72	0.540	1.411	18.0	11.1	7/16
3/8" NPT	17.14	0.675	1.411	18.0	14.3	9/16
1/2" NPT	21.34	0.840	1.814	14.0	17.9	45/64
3/4" NPT	26.67	1.050	1.814	14.0	23.0	29/32
1" NPT	33.40	1.315	2.209	11.5	29.4	1-5/32
1-1/4" NPT	42.16	1.660	2.209	11.5	38.1	1-1/2
1-1/2" NPT	48.26	1.900	2.209	11.5	44.2	1-47/64
2" NPT	60.33	2.375	2.209	11.5	56.1	2-7/32

Tem uma sugestão?

Solicite uma nova ferramenta ou sugira melhorias — junte-se à nossa comunidade no Slack!

Deixar feedback no Slack

What is Thread Pitch Identification?

Thread pitch identification is the process of determining the thread standard (NPT, BSP, UNC/UNF, or Metric) of an unknown fastener or fitting by measuring its outer diameter and thread pitch. NPT threads are tapered at 1°47' with a 60° thread angle and seal on the threads themselves. BSP threads have a 55° angle and can be parallel (BSPP) or tapered (BSPT). UNC/UNF are straight threads with 60° angle defined by threads per inch. Metric threads use a 60° angle with pitch measured in millimeters. Confusing NPT and BSP is a common cause of cross-threading and leaks.

How to Use This Identifier

Measure the outer diameter of the thread crests using calipers (mm or inches)
Count threads per inch (TPI) using a thread pitch gauge, or measure pitch in mm between thread crests
Select whether you measured pitch in mm or TPI
Click Identify to see all matching thread standards and their specifications
Compare the SVG thread profiles to understand the differences between matching standards

Frequently Asked Questions

How do I tell NPT from BSP threads apart?

The key differences are: (1) Thread angle — NPT is 60°, BSP is 55°. (2) Taper — NPT is always tapered at 1°47'; BSP can be parallel (BSPP) or tapered (BSPT). (3) TPI values differ at the same nominal size. For example, 1/2" NPT has 14 TPI while 1/2" BSP has 14 TPI as well, but the major diameters differ (0.840" vs 0.825").

Can I use NPT fittings with BSP threads?

No, NPT and BSP threads are not interchangeable even when they appear similar. The different thread angles (60° vs 55°) and taper dimensions mean they will cross-thread and leak. Use the correct adapter fitting or replace one side with the matching standard. PTFE tape or pipe dope cannot compensate for the mismatch.

What is the difference between UNC and UNF?

UNC (Unified National Coarse) has fewer threads per inch and is the standard for general purpose fastening — easier to assemble and more resistant to cross-threading. UNF (Unified National Fine) has more TPI and provides stronger holding power in the same bolt diameter, better vibration resistance, and finer adjustment. Example: 1/4-20 UNC vs 1/4-28 UNF.